IN DETAIL
LiberaToe Platform

LiberaToe-6 (6L)
3 Route Modes
You can choose a route mode out of 3 ones by MODE/TAP foot switch depending on the play.
-
IM(Improvisation) mode: This mode enables 6 slots/loops to work independently as in the pedalboard. Each slot/loop can be turned on or off by corresponding foot switch. Each slot/loop also can be toggled between two channels (green and red) through the button setting beforehand.
-
PG(Program) mode: This mode functions as a standard programmable system. Six slots/loops, input buffer, frequency enhancer, and two external controls can be immediately controlled by four patch switch. Up to 100 banks can be loaded by Bank Up(▲)/Down(▼) switches. So you have 400 presets.
-
Mb(Ambidextrous) mode: This mode is a mix of IM and PG mode. It basically looks like the IM mode, but also lets you mix use with PG mode.
Dual Channel
All the slots/loops support dual channel. The channels can be selected or switched each other. Depending on the button color setting, the channels are determined as below :
-
Green: The module/loop runs green channel which enables green knobs of the modules (or green channel loop in a connection module).
-
Red: The module/loop runs red channel which enables red knobs of the modules (or red channel loop in a connection module).
-
Flickering : You can use the foot switch to switch between the two channels immediately, activated by double clicking the button prior. The channel can be turned off by long push on the foot switch.
Controllable Resource
-
Slots/Loops: Dual channel support each
-
Reverse and Parallel: The settings change the route dynamically
-
Enhancer: More clarity, dynamics through adjusting Hi, Lo frequency knobs
-
Input Buffer: Specially designed high class buffer preventing tone loss
-
External Control: Two controls for outside gears such as an amp channel, which follow LC/LO/MC/MO conventions
Manual Operation
-
Cabinet Simulator: British amp speaker cabinet simulator for direct connection to mixer, recorder, or PA
-
Output Buffer: Transparent line driver
-
Master Volume: equipped with larger knob
-
GND Lift: Prevent ground loop noise just in case
I/O
-
Input / Output: standard 1/4 mono jack
-
Send / Return: located between 3rd and 4th slot(loop), half-normalled wiring
-
DC input: 24V 3A (center positive)
-
DC output: 9V/18V (center negative), contingent for auxiliary power
-
USB power: 5V DC output
-
Extension jack: for connection with LiberaToe-4/4L, entire 10 slots/loops are centrally controlled (to be released)
-
Switch Box jack: for connection with separate switch box
-
External control: 1/4 stereo TRS jack. Tip is for Ctrl 1 while Ring is for Ctrl 2
-
Custom socket : future custom purpose
LiberaToe-4 (4L)
3 Route Modes
You can choose a route mode out of 3 ones by the right most “W” foot switch.
-
IM(Improvisation) mode: This mode enables 4 slots/loops to work independently as in the pedalboard. Each slot/loop can be turned on or off by corresponding foot switch. Each slot/loop also can be toggled between two channels (green and red) through the button setting beforehand.
-
EX(Exclusive) mode: In this mode, you can turn only one slot/loop on since all the loops work exclusively each other. You will also be able to turn it off (bypass) by pushing the same foot switch briefly once again. Additionally If you set the loop to flash by double-click on the button, you can switch between the two channels whenever you push the same foot switch briefly. Of course you can turn it off (bypass) when you hold it (more than 0.4 sec).
-
Mb(Ambidextrous) mode: This mode is a mix of IM and preset mode. It basically works like the general programmable loop, but also lets the unassigned foot switches to be used as like in IM mode.
Dual Channel
All the slots/loops support dual channel. The two channels can be selected independently or switched each other. Depending on the button color setting, the channels are determined as below :
-
Green: The module/loop runs green channel which enables green knobs of the modules (or green channel loop in a connection module).
-
Red: The module/loop runs red channel which enables red knobs of the modules (or red channel loop in a connection module).
-
Flickering: You can use corresponding foot switch to switch between the two channels immediately, activated by double clicking the button prior. The channel can be turned off by holding on the foot switch.
Controllable Resource
-
Slots/Loops: Dual channel support each
-
Parallel: Signals split to loop 3 and 4 to be merged at the ends
Manual Switched
-
Input Buffer: Natural signal preservation (two buffers between loop 2 and 3 turn on when parallel feature works)
I/O
-
Input / Output: Standard 1/4 mono jack
-
DC input: 24V 3A (center positive)
-
Extension jack: For connection with LiberaToe-6/6L, entire 10 slots/loops are centrally controlled (to be released)
-
Switch Box jack: For connection with separate switch box
_edited.png)